$80.00

If your current shotgun bead is too small why change out the entire bead? We make beads that fit over the existing bead on your shotgun. They are offered in two sizes 7/32 and 1/4" and are made from solid brass. To get the correct size "mic" your existing bead size, then order the one that matches your current bead size. We offer them in three under bead sizes .125 , .155 and .177. When you receive your new sight just simply place it over your current bead, making sure your barrel is on a flat surface and tap the new sight on with a light mallet. Select corresponding sizes below.

1873 "No Bite" Trigger System

1873 "No Bite" Straight Trigger System

STAINLESS STEEL FOLLOWERS FOR UBERTI 1873.

$29.00

Pic 3

Picture 1 Use Acetone or Rubbing alcohol to remove dirt, powder, or grease from the blade
Picture 2 Use a strip of sand paper to rough up the sides of sight blade
Picture 3 Apply the retainer adhesive and wait 15mins to cure, Hold sight on for a few minutes
Picture 4 Use a dremel, file, or sand paper to grid down to your POA

The new drop in "No Fit No Adjustment" trigger system is our latest addition to the Sure Hit product line. Each Sure Hit product is proudly USA made in our state of the art machine shop. This trigger system comes set up with a match grade upper sear and lower trigger that is custom tuned for a crisp trigger pull. Each trigger system has a small rebound trigger spring built in to keep the trigger from moving while being rapidly fired. This along with the dehorned corners will help eliminate the dreaded 1873 trigger bite.

Ruger Hammer Spring 13lb. - Ruger Vaquero/Blackhawk

Sight - Shotgun Bead Sight

$125.00

Hard to find Browning Side by Side Lever Spring! This fits the Korean and Japanese Guns that use a screw to hold in the spring.

Browning Side by Side Lever Spring

Low profile hammers that fit Ruger Super Black Hawks AND New Model Vaqueros.

New Brass Carriers for 1860/1866/1973 Uberti

F&D Online Store

Ruger Super Blackhawk Hammers

Brass sight slips snuggly over your original Marbles style site that is on a 66, 73 or a Marlin. There are 2 different sizes. The Medium is for small far targets and the Large is for big and close. SASS Approved

This "Sure Hit" brass sight will easily fit right over your existing Single Action Pistol whether it be a Colt, Colt Clone or Ruger Vaquero (New or Old Model), USFA or Taylor. They provide a wider sight, making target aquisition extremely fast!

Sight - "Sure Hit" Pistol Sights (Pair)



The magazine follower replaces the factory orange plastic factory followers. Over time the cleaning solvents and everyday use will cause the plastic followers to crack and break. When this happens it will cause your magazine spring to stick inside the tube and not function. Stainless Steel - Fits All Calibers

These stainless steel mag springs prevent rust from building up in your lever action magazine tube. Over time the moisture will cause the factory metal spring to corrode and rust. When this happens it will prevent the spring from working freely to push the next round down the tube smoothly . These springs are shipped 26 inches long. When installing leave 3" sticking out of the factory mag tub and trim off the remaining amount of spring.

$100.00

$15.00

STAINLESS STEEL MAGAZINE SPRING FOR UBERTI 1873

TEMPORARILY OUT OF STOCK

$9.00

$69.00

$135.00


Pic 3.1

$25.00

Pic 1

1860/1866/1873 Uberti Hard Black annodized Carrier. If you are looking for a high quality, lightweight carrier, this is the one for you! Only available in 38 Special/357 Mag.

$12.00

Pic 2

Pic 4

Sight - "Sure Hit" Rifle Sight

$20.00

Type your paragraph here.

FOR SMALL AND LARGE CALIBERS. WILL WORK IN UBERTI MADE MODELS 1866 & 1873. ALREADY PRE-LIGHTENED WITH SURE HIT LOGO. READY TO DROP IN. 
WHEN ORDERING SPECIFY THE CALIBER YOU NEED

You asked for it, We delivered! Now introducing the 1873 No Bite Straight Trigger. Available as a complete trigger system that comes set up with a match grade upper sear and rebound trigger spring, or available as just the lower straight trigger to re use the upper sear that you already have! As always each Sure Hit product is proudly USA made in our state of the art machine shop.

1860/1866/1873 Uberti Aluminum Carrier

$135.00

Competition 13 lb. hammer spring for the Ruger Vaquero/Blackhawk. These are tuned, 13 lb. zinc coated springs that will not corrode or rust. This spring will ignite all brands of primers and yet still give your revolver the smooth reliable action you desire.